OEM reverse camera

Discussion around Insane Audio's super awesome new JL3001 for your JL Wrangler or JT Gladiator!
Post Reply
johnparjr
Posts: 3
Joined: Fri Jan 24, 2020 4:41 pm

OEM reverse camera

Post by johnparjr » Fri Feb 14, 2020 7:44 pm

So the camera is not as clear as it was with the OEM radio its a little grainy any way to clear it up or make it brighter

InsaneAudioSupport
Posts: 409
Joined: Mon Sep 01, 2014 1:09 pm

Re: OEM reverse camera

Post by InsaneAudioSupport » Sat Feb 15, 2020 12:15 pm

Hi, John. For the JL3001 we are re-using your OEM camera so the picture should essentially be exactly the same. Unfortunately, we have no control over the OEM camera's resolution and admittedly it isn't as sharp as, say, Insane Audio's IACAM1 or IACAM2. But this is the OEM camera. It may look a little pixalated just by virtue of the fact that we are expanding the image to a 9" screen. But it's the exact same image feed so the resolution is essentially the same.

The only other thing w'd recommend you do is to perhaps check your connections. Make sure everything is nice and clean (especially the RCA connections to your OEM camera). You may want to wrap each connection with electrical tape as well.

Please let us know!

danelizer
Posts: 3
Joined: Thu May 07, 2020 6:32 am

Re: OEM reverse camera

Post by danelizer » Sat May 09, 2020 3:30 am

I just recently installed my JL3001 and noticed the backup camera picture looks washed out compared to the OEM picture which was very colorful. It’s not black and white. Maybe too much brightness. Anyway to adjust the picture ion the JL3001? I will be installing the Insane forward camera next week and will do a comparison.
Danelizer

InSaNeAuDiOSupport5
Posts: 183
Joined: Fri Feb 03, 2017 11:59 am

Re: OEM reverse camera

Post by InSaNeAuDiOSupport5 » Tue May 12, 2020 2:11 pm

Hey there!

Congratulations on the installation of the JL3001! 🙂

Coming to the query at hand, we suggest you check all your connections, paying particular attention to the RCA cable (Make sure you're using the correct RCA cables) and make sure you're is using the Reverse CVBS.

Connect 'REVERSE CVBS OUTPUT' (from the Black CanBus module: MODEL: XSYBOX-006) to the 'Backup Cam' from the JL CanBus wiring harness (make sure to connect the Backup Cam wire from the black connector that plugs into the back of our head unit) and you should be good to go.

Please refer to video installation guide that will help you with the connection: https://insaneaudio.com/JL3001_VInstall ... stall.html

Just to let you know, Insane Audio’s JL3001 re-uses your OEM backup camera so the resolution and image is exactly the same. The only difference is that it’s a bit larger now on our 9” screen and since the OEM camera doesn’t have very high resolution this is a bit similar to zooming in or expanding a picture on any device so it will be a little less clear but this is the exact same image only expanded a bit. Admittedly the OEM camera isn't exactly high def, but it should certainly look good.

y84media
Posts: 4
Joined: Tue May 19, 2020 5:08 pm

Re: OEM reverse camera

Post by y84media » Tue May 26, 2020 4:10 pm

InsaneAudioSupport wrote:
Sat Feb 15, 2020 12:15 pm
Unfortunately, we have no control over the OEM camera's resolution and admittedly it isn't as sharp as, say, Insane Audio's IACAM1 or IACAM2. But this is the OEM camera. It may look a little pixalated just by virtue of the fact that we are expanding the image to a 9" screen.
I’m excited to find out what the resolution of these cameras (IACAM1 & IACAM2) are, especially using composite (analog Non-HD) connections.

Post Reply